91.100.99 (Other construction materials) 标准查询与下载

ASTM D6525/D6525M-14 测量成卷冲刷防护产品公称厚度的标准试验方法

5.1 Thickness is one of the basic physical properties used to control the quality of permanent rolled erosion control products. Thickness values may aid in the calculation of other permanent rolled erosion control product parameters. Thickness however is not generally an indication of field performance and generally should not be used in specifications. This test method is developed to aid manufacturers, designers, and end users in comparing the thickness of permanent rolled erosion control products through the use of an accepted ASTM standard. 5.2 The thickness of permanent rolled erosion control products may vary considerably depending on the pressure applied to the specimen during measurement. Where observed changes occur, thickness decreases when applied pressure is increased. To minimize variation, specific sample size and applied pressure are indicated in this test method to ensure all results are comparable. 5.3 This test method may be used for acceptance testing of commercial shipments of permanent rolled erosion control products, but caution is advised since information on between-laboratory precision is incomplete. Comparative tests in accordance with 5.3.1 may be advised. 5.3.1 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are formed from a lot of material of the type in question. The test specimens should be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Students t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If bias is found, either its cause must be found and corrected or the purchaser and supplier must agree to interpret future tests in light of the known bias. Note 1: The user should be aware that the compressibility of the materials, their rebound characteristics, and the like will also affect the thickness of the permanent rolled erosion control products following the time they are rolled up on rolls, shipped, and stored. 1.1 This test method covers the measurement of the nominal thickness of permanent rolled erosion control products. 1.2 This test method does not provide thickness values for permanent rolled erosion control products under variable compressive stresses. This test method determines nominal thickness, not necessarily minimum thickness. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used......

Standard Test Method for Measuring Nominal Thickness of Rolled Erosion Control Products

ASTM E2134/E2134M-14 评估外部绝缘和饰面系统(EIFS)拉伸-粘着特性的标准试验方法

5.1 Maintenance of adequate tensile adhesion of EIFS components to each other, and to the substrate are essential for long term performance of the system. 5.2 The tensile-adhesion properties obtained by this test method are not purported to be representative of wind load or other structural and moisture related properties of the EIFS wall assembly. Tensile-adhesion properties using this test method are used as one of the factors in evaluating substrates and to compare adhesives. 1.1 This test method evaluates the tensile-adhesion performance of an exterior insulation and finish System (EIFS) or its individual components by two different procedures: Procedure A, Dry Conditioning and Testing of Specimens; and Procedure B, Wet Conditioning and Testing of Specimens. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating the Tensile-Adhesion Performance of an Exterior Insulation and Finish System (EIFS)

ASTM D4016-14 使用旋转粘度计测定化学薄泥浆粘度和凝胶时间的标准试验方法(实验室法)

5.1 This test is intended for materials that will penetrate soil voids and rock fissures. Viscosity alone is not necessarily an exact index of grout penetrability. 1.1 This test method covers the determination of viscosity of catalyzed chemical grouts with a rotational viscometer (laboratory method), over the range from 1.0 mPa·s to 1000 mPa·s (1.0 to 1000 cP). 1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.2.1 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose of obtaining the data, special purpose studies, or any consideratons for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design. 1.3 The values stated in SI units are the standard. Other units provided in parentheses are for the convenience of the user. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Viscosity and Gel Time of Chemical Grouts by Rotational Viscometer 40;Laboratory Method41;

ASTM D6662-13 聚烯泾基塑料木材盖板的标准规范

1.1 This specification covers polyolefin-based plastic lumber products for use as exterior residential decking boards. 1.2 Plastic lumber products are currently made predominantly with recycled polyolefin plastics (in particular high-density polyethylene) where the products are more or less non-homogenous in the cross-section. However, this specification is also potentially applicable to similar manufactured plastic products made from other plastic and plastic composite materials that have non-homogenous cross-sections. 1.3 This specification details a procedure to calculate recommended span lengths for spacing of support joists. This procedure was developed using experimental data from a typical unreinforced plastic lumber made predominantly from recycled high-density polyethylene. The methodology to develop span lengths for other types and compositions of plastic lumber is detailed in Appendix X1 of this standard. 1.4 The values are stated in inch-pound units, as these are currently the most common units used by the construction industry. Equivalent SI units are indicated in parentheses. However, the units stated for irradiance exposure in the weatherability section (6.3) are in SI units as these are the units commonly used for testing of this type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1—There is no similar or equivalent ISO Standard.

Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards

ASTM C1397-13 PB级外部绝缘和装饰系统(EIFS)及带排水管道的EIFS的应用的标准实施规程

4.1 This practice provides minimum requirements for the application of Class PB EIFS and EIFS with Drainage (see Specification E2568). The requirements for materials, mixtures, and details shall be contained in the project plans and specifications. See Guide E1825 for guidance. 1.1 This practice covers the minimum requirements and procedures for field or prefabricated application of Class PB Exterior Insulation and Finish Systems (EIFS) and EIFS with Drainage. Class PB EIFS are systems applied over insulation board, in which the base coat ranges from not less than 1/16 in. (1.6 mm) to 1/4 in. (6.4 mm) in dry thickness, depending upon the number of nonmetallic reinforcing mesh layers encapsulated in the base coat (see Specification E2568). The base coat is then covered with a finish coat of varying thickness in a variety of textures and colors. EIFS with Drainage provides a mechanism to drain incidental moisture 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The text of this practice references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as a requirement of the standard. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Class PB Exterior Insulation and Finish Systems lpar;EIFSrpar; and EIFS with Drainage

ASTM F1645/F1645M-12 蜂窝芯材料中水移动特性的标准试验方法

Water permeability is a fundamental physical property that can be used in conjunction with other properties to characterize honeycomb sandwich core materials. Migration testing can be used to characterize and compare the relative permeability of honeycomb core materials to water. This test method provides a standard method of characterizing the rate of water migration within honeycomb sandwich core materials for design properties, material specifications, research and development applications, and quality assurance. Factors that influence water migration rate characteristics of honeycomb sandwich core materials and shall therefore be reported include the following: core material, methods of material fabrication, core geometry (cell size), core thickness, core thickness uniformity, cell wall thickness, specimen geometry, specimen preparation, specimen conditioning, facing material, facing permeability, adhesive permeability, adhesive thickness, and methods of mass, volume, and water column height measurement.1.1 This test method covers the determination of water migration in honeycomb core materials. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Within the text the inch-pound units are shown in brackets. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Water Migration in Honeycomb Core Materials

ASTM D6525-12 测量成卷冲刷防护产品公称厚度的标准试验方法

1.1 This test method covers the measurement of the nominal thickness of permanent rolled erosion control products. 1.2 This test method does not provide thickness values for permanent rolled erosion control products under variable compressive stresses. This test method determines nominal thickness, not necessarily minimum thickness. 1.3 The values stated......

Standard Test Method for Measuring Nominal Thickness of Rolled Erosion Control Products

ASTM D6662-09 聚烯烃基塑料木材盖板的标准规范

1.1 This specification covers polyolefin-based plastic lumber products for use as exterior residential decking boards. 1.2 Plastic lumber products are currently made predominantly with recycled polyolefin plastics (in particular high-density polyethylene) where the products are more or less non-homogenous in the cross-section. However, this specification is also potentially applicable to similar manufactured plastic products made from other plastic and plastic composite materials that have non-homogenous cross-sections. 1.3 This specification details a procedure to calculate recommended span lengths for spacing of support joists. This procedure was developed using experimental data from a typical unreinforced plastic lumber made predominantly from recycled high-density polyethylene. The methodology to develop span lengths for other types and compositions of plastic lumber is detailed in Appendix X1 of this standard. 1.4 The values are stated in inch-pound units, as these are currently the most common units used by the construction industry. Equivalent SI units are indicated in parentheses. However, the units stated for irradiance exposure in the weatherability section (6.3) are in SI units as these are the units commonly used for testing of this type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;There is no similar or equivalent ISO Standard.

Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards

ASTM C1397-09 PB级外部绝缘和装饰系统的应用的标准实施规程

This practice provides minimum requirements for the application of Class PB EIFS and EIFS with Drainage (see Specification E 2568). The requirements for materials, mixtures, and details shall be contained in the project plans and specifications. See Guide E 1825 for guidance.1.1 This practice covers the minimum requirements and procedures for field or prefabricated application of Class PB Exterior Insulation and Finish Systems (EIFS) and EIFS with Drainage. Class PB EIFS are systems applied over insulation board, in which the base coat ranges from not less than 1/16 in. (1.6 mm) to ¼ in. (6.4 mm) in dry thickness, depending upon the number of nonmetallic reinforcing mesh layers encapsulated in the base coat (see Specification E 2568). The base coat is then covered with a finish coat of varying thickness in a variety of textures and colors. EIFS with Drainage provides a mechanism to drain incidental moisture 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The text of this practice references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as a requirement of the standard. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Class PB Exterior Insulation and Finish Systems (EIFS) and EIFS with Drainage

ASTM E1730-09 结构夹层板芯板用硬质泡沫塑料标准规范

1.1 This specification covers rigid, closed cell, polyurethane and polyisocyanurate thermal insulation for sandwich panels used in shelter construction for exposure to ambient temperatures of −25° to 160°F (−32° to 71°C). Painted surfaces of shelters in actual field use reach temperatures of 200°F (93°C). The materials in this specification must be capable of withstanding processing, (laminating) temperatures of 110°C (230°F). 1.2 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only. 1.3 The following precautionary caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Rigid Foam for Use in Structural Sandwich Panel Cores

ASTM D6662-07 聚烯烃基塑料木装饰板的标准规范

1.1 This specification covers polyolefin-based plastic lumber products for use as exterior residential decking boards.1.2 Plastic lumber products are currently made predominantly with recycled polyolefin plastics (in particular high-density polyethylene) where the products are more or less non-homogenous in the cross-section. However, this specification is also potentially applicable to similar manufactured plastic products made from other plastic and plastic composite materials that have non-homogenous cross-sections.1.3 This specification details a procedure to calculate recommended span lengths for spacing of support joists. This procedure was developed using experimental data from a typical unreinforced plastic lumber made predominantly from recycled high-density polyethylene. The methodology to develop span lengths for other types and compositions of plastic lumber is detailed in Appendix X1 of this standard.1.4 The values are stated in inch-pound units, as these are currently the most common units used by the construction industry. Equivalent SI units are indicated in parentheses. However, the units stated for irradiance exposure in the weatherability section (6.3) are in SI units as these are the units commonly used for testing of this type.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1There is no similar or equivalent ISO Standard.

Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards

ASTM D6662-06 聚烯烃基塑料木装饰板的标准规范

1.1 This specification covers polyolefin-based plastic lumber products for use as exterior residential decking boards.1.2 Plastic lumber products are currently made predominantly with recycled polyolefin plastics (in particular high-density polyethylene) where the products are more or less non-homogenous in the cross-section. However, this specification may also be applicable to similar manufactured plastic products made from other plastic and plastic composite materials that have non-homogenous cross-sections.1.3 This specification details a procedure to calculate recommended span lengths for spacing of support joists. This procedure was developed using experimental data from a typical unreinforced plastic lumber made predominantly from recycled high-density polyethylene. The methodology to develop span lengths for other types and compositions of plastic lumber is detailed in Appendix X1 of this standard.1.4 The values are stated in inch-pound units, as these are currently the most common units used by the construction industry. Equivalent SI units are indicated in parentheses. However, the units stated for irradiance exposure in the weatherability section (6.3) are in SI units as these are the units commonly used for testing of this type.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 18212;There is no similar or equivalent ISO Standard.

Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards

ASTM C1516-05(2011) 直接应用的外部装饰系统应用的标准实施规程

This practice provides minimum requirements for the application of Direct-applied Exterior Finish Systems. The requirements for materials, mixtures, and details shall be contained in the project plans and specifications.1.1 This practice covers the minimum requirements and procedures for field application of Direct-applied Exterior Finish Systems (DEFS). Direct-applied exterior finish systems are coating systems applied over various substrates with non-metallic reinforcing mesh, in which the base coat ranges from not less than 1/16in. (1.6 mm) to 3/32 in. (2.4 mm) in dry thickness, depending on the mass of the reinforcing mesh. This base coat is subsequently covered with a finish coat that is available in a variety of textures and colors. 1.2 The values stated in inch-pound units are to be regarded as the standard. The metric values given in parentheses are approximate and are provided for information purposes only. 1.3 This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Direct-Applied Exterior Finish Systems

ASTM C1516-05 直接应用的外部装饰系统应用的标准实施规程

This practice provides minimum requirements for the application of Direct-applied Exterior Finish Systems. The requirements for materials, mixtures, and details shall be contained in the project plans and specifications.1.1 This practice covers the minimum requirements and procedures for field application of Direct-applied Exterior Finish Systems (DEFS). Direct-applied exterior finish systems are coating systems applied over various substrates with non-metallic reinforcing mesh, in which the base coat ranges from not less than 1/16in. (1.6 mm) to 3/32 in. (2.4 mm) in dry thickness, depending on the mass of the reinforcing mesh. This base coat is subsequently covered with a finish coat that is available in a variety of textures and colors.1.2 The values stated in inch-pound units are to be regarded as the standard. The metric values given in parentheses are approximate and are provided for information purposes only.1.3 This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Direct-Applied Exterior Finish Systems

ASTM E1730-04 结构夹层板芯板用硬质泡沫塑料标准规范

1.1 This specification covers rigid, closed cell, polyurethane and polyisocyanurate thermal insulation for sandwich panels used in shelter construction for exposure to ambient temperatures of - 25 to 160176;F (- 32 to 71176;C). Painted surfaces of shelters in actual field use reach temperatures of 200176;F (93176;C). The materials in this specification must be capable of withstanding processing, (laminating) temperatures of 110176;C (230176;F).1.2 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.1.3 The following precautionary caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Rigid Foam for Use in Structural Sandwich Panel Cores

ASTM C1516-02 直接应用的外部精整系统应用的标准实施规范

1.1 This practice covers the minimum requirements and procedures for field application of Direct-applied Exterior Finish Systems (DEFS). Direct-applied exterior finish systems are coating systems applied over various substrates with non-metallic reinforcing mesh, in which the base coat ranges from not less than 1/16in. (1.6 mm) to 3/32 in. (2.4 mm) in dry thickness, depending on the mass of the reinforcing mesh. This base coat is subsequently covered with a finish coat that is available in a variety of textures and colors.1.2 The values stated in inch-pound units are to be regarded as the standard. The metric values given in parentheses are approximate and are provided for information purposes only.1.3 This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Direct-Applied Exterior Finish Systems

ASTM E1730-02 叠层结构芯板用硬质泡沫的标准规范

1.1 This specification covers rigid, closed cell, polyurethane and polyisocyanurate thermal insulation for sandwich panels used in shelter construction for exposure to ambient temperatures of 25 to 160176;F (32 to 71176;C). Painted surfaces of shelters in actual field use reach temperatures of 200176;F (93176;C). The materials in this specification must be capable of withstanding processing, (laminating) temperatures of 110176;C (230176;F).1.2 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.1.3 The following precautionary caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Rigid Foam for Use in Structural Sandwich Panel Cores

ASTM C1397-02 PB级外部绝缘和精整系统的应用的标准实施规程

1.1 This practice covers the minimum requirements and procedures for field or prefabricated application of Class PB Exterior Insulation and Finish Systems (EIFS). Class PB EIFS are systems applied over insulation board, in which the base coat ranges from not less than 1 /16 in. (1.6 mm) to 1 /4 in. (6.4 mm) in dry thickness, depending upon the number of nonmetallic reinforcing mesh layers encapsulated in the base coat. The base coat is then covered with a finish coat of various thickness in a variety of textures and colors. 1.2 This standard does not cover Class PB EIFS with drainage. Consult the EIFS producer for information.1.3 The values stated in inch-pound units are to be regarded as the standard. The metric values given in parentheses are approximate and are provided for information purposes only.1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as a requirement of the standard.1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Class PB Exterior Insulation and Finish Systems

ASTM D4016-02 用布鲁克菲尔德粘度计测定化学灌浆粘度的标准试验方法(实验法)

This test is intended for materials that will penetrate soil voids and rock fissures. Viscosity alone is not necessarily an exact index of grout penetrability. Note 18212;The quality of the result produced by this test method is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with of Practice D 3740 does not in itself assure reliable results. Reliable results depend on mnay factors; of Practice D 3740 provides a means of evaluating some of those factors.1.1 This test method covers the determination of viscosity of catalysed chemical grouts with the Brookfield viscometer (laboratory method), over the range from 1.0 to 1000 cP (0.001 to 1 Pa183;s).1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Viscosity of Chemical Grouts by Brookfield Viscometer (Laboratory Method)

ASTM E2134-01 评定外部绝缘和涂层系统拉伸-粘着特性的标准试验方法

1.1 This test method evaluates the tensile-adhesion performance of an exterior insulation and finish System (EIFS) or its individual components by two different procedures: Procedure A, Dry Conditioning and Testing of Specimens; and Procedure B, Wet Conditioning and Testing of Specimens.1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating the Tensile-Adhesion Performance of an Exterior Insulation and Finish System (EIFS)